TeCHSupport
Collects information required to debug a given feature or subfeature
- TeCHSupport
Shortest form:
tchs.Collect debug information about a feature and print it to the console: the feature’s diag-shell commands, its registers and memories, and its SDK software-state dumps.
techsupport basiccollects general setup information.techsupport allrunsbasicand then every feature this chip supports. This is the SDK’s own collector. It is separate from SONiC’sshow techsupport, which runs a fixed list ofbcmcmdcommands (scripts/generate_dump (show techsupport collector)), and from the SAI’sBCMSAI TechSupport(BCMSAI).The feature name must be typed in full. On Trident 3 these features are supported:
ifp,vfp,efp,mpls,cos,mmu,vxlan,niv,vlan,riot,flex_flow,load-balance,l3uc,l3mc,cmic,visibility,warmbootandcancun. The other features in the built-in help (etrap,int,histogram,alpm,oam,tcb,dgm,pstat,PHY,LEDUP,flowtracker) printcommand "techSupport <name>" not supported on chip <chip>.Options after the feature name narrow what is collected. Without any option, everything is collected. Each collected command is framed by
>>>…Output of "<command>" start>>>…and<<<…Output of "<command>" end<<<…lines. Registers are read withgetreg chgand memories withdump chg, so by default only values that differ from the reset values appear.diag: only the diag-shell commands.reg: only registers.mem: only memories.sw: only the software-state dumps.verbose: dump whole tables. By default only entries that differ from their reset values are dumped.list: print what would be collected, without running anything.generate-script: print the collection as a script of commands, without running it. The built-in help does not mention it.
basicandalltake no options.Safety on a running switch Form
Effect
basic,all, feature collections,list,generate-scriptRead-only, but output can be very large and keeps the shell busy while it runs. On a SONiC Trident 3 switch a feature with
diagtook 1 to 3 seconds;basicprinted about 22,000 lines in 13 seconds,cancun(all of its parts) 12,500 lines in 15 seconds,cos diag48,000 lines, andallmore than 27 MB in over ten minutes.basicalso runsshow counters, which moves the “changed” baseline ofshow counters.visibilitySends a trace packet into the switch pipeline. With trace option
0x4(forward) the packet may be forwarded.Hardware-validated — Run only the MMU-related diag commands
drivshell> techsupport mmu diag >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "ps" start>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> ena/ speed/ link auto STP lrn inter max cut loop port link Lns duplex scan neg? state pause discrd ops face frame thru? back encap ce0( 1) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce1( 5) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE xe0( 9) up 1 10G FD SW No Forward Untag F XFI 9122 No IEEE xe1( 10) up 1 10G FD SW No Forward Untag F XFI 9122 No IEEE xe2( 11) up 1 10G FD SW No Forward Untag F XFI 9122 No IEEE xe3( 12) up 1 10G FD SW No Forward None F XFI 9122 No IEEE ce2( 13) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce3( 17) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce4( 21) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce5( 25) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce6( 29) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce7( 33) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce8( 37) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce9( 41) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce10( 45) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce11( 49) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce12( 53) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce13( 57) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce14( 61) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE xe4( 66) !ena 1 10G FD SW No Forward Untag F XFI 9122 No IEEE ce15( 67) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce16( 71) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce17( 75) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce18( 79) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce19( 83) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ...
Hardware-validated — List what “techsupport l3uc” would collect, without running it
drivshell> techsupport l3uc list List of Diag commands: >>>>>>>>>>>>>>>>>>>>>> l2 show vlan show l3 intf show l3 egress show l3 multipath show l3 l3table show l3 defip show l3 alpm show l3 ip6host show l3 ip6route show l3 tunnel_init show l3 tunnel_term show trunk show List of Memory Table names: >>>>>>>>>>>>>>>>>>>>>>>>>>> SOURCE_TRUNK_MAP_MODBASE ING_DEVICE_PORT L3_TUNNEL L3_TUNNEL_DATA_ONLY L3_TUNNEL_ONLY SOURCE_VP_2 PARSER1_IPV4_IN_IPV6_PREFIX_MATCH_TABLE PARSER2_IPV4_IN_IPV6_PREFIX_MATCH_TABLE LPORT_TAB SOURCE_TRUNK_MAP_TABLE VFP_POLICY_TABLE ...
- TeCHSupport basic
Collect basic setup information by running, in order:
a,version,config show,show counters,linkscan,ps,lls sw,hsp,soc,fp show,show pmap,phy info,show params,show features,switchcontrol,switchcontrol pbm=all,dump soc diff,dump pcic,pvlan show,age,knetctrl netif show,knetctrl filter show,show statistics,cstat get allandcancun stat. Read-only, but it runs for a while.Hardware-validated
drivshell> techsupport basic >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "a" start>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Attach: Unit 0 (BCM56870_A0): attached (current unit) <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "a" end<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "version" start>>>>>>>>>>>>>>>>>>>>>>>>>>>> Broadcom Command Monitor: Copyright (c) 1998-2026 Broadcom Release: sdk-6.5.35-SP1 built 20260930 (Wed Sep 30 11:49:47 2026) SDK version 6.5.35 : 1.19 From root@4206781cd07d:/__w/1/s/output/x86-xgsall-deb/xgs-sdk-src/hsdk-all-6.5.35 Platform: unknown OS: Unix (Posix) <<<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "version" end<<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>>>>>Output of "config show" start>>>>>>>>>>>>>>>>>>>>>>>>>> phy_chain_rx_polarity_flip_physical{16.0}=0x1 phy_chain_tx_polarity_flip_physical{34.0}=0x0 phy_chain_tx_lane_map_physical{49.0}=0x2103 phy_chain_rx_lane_map_physical{89.0}=0x2031 phy_chain_rx_polarity_flip_physical{94.0}=0x1 lpm_scaling_enable=1 phy_chain_rx_polarity_flip_physical{59.0}=0x0 phy_chain_tx_polarity_flip_physical{77.0}=0x0 phy_chain_rx_polarity_flip_physical{1.0}=0x0 phy_chain_rx_lane_map_physical{113.0}=0x2031 ...
- TeCHSupport all
Run
basicand then every supported feature in turn. Each step is framed bySTART: Executing "techSupport <name>".andEND: …lines, followed by the time it took. Read-only, but it takes a long time.Warning
On a SONiC Trident 3 switch
techsupport allran for more than ten minutes and printed more than 27 MB. It keeps running insidesyncdafter thebcmcmdclient times out, and until it finishes no otherbcmcmdorbcmshsession gets the shell. Run it only when you need it, givebcmcmda long timeout (-t 3600) and send the output to a file; for most purposesbasicor a single feature is enough.Unvalidated
drivshell> techsupport all
- TeCHSupport visibility <data=<hex> | file=<path>> sourceport=<port> [options=<flags>] [raw]
Trace a packet through the switch pipeline as if it arrived on
sourceport. Give the packet as hex bytes (data=) or a file (file=). The trace options are listed in the built-in help (0x1to0x10).rawdumps the raw trace data. Withoutrawthe packet is sent with thetxcommand, which may not be available in SONiC. This sends a packet into the pipeline; see the safety table.Unvalidated — Replace <hex_bytes> with at least 16 bytes of packet data
drivshell> techsupport visibility data=<hex_bytes> sourceport=1 raw
- TeCHSupport ifp [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect ingress field processor (IFP) debug information. Diag commands run: fp show. Software dumps: dump sw ifp. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport ifp diag >>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "fp show" start>>>>>>>>>>>>>>>>>>>>>>>>>>>> FP: Range ID=1, flag=0x1, min=34048, max=35072, hw_index=0(0), style=BCM56504 FP: unit 0: PIPELINE STAGE INGRESS FP: :tcam_sz=18432(0x4800), tcam_slices=12, tcam_ext_numb=0, PIPELINE STAGE EGRESS FP: :tcam_sz=2048(0x800), tcam_slices=4, tcam_ext_numb=0, PIPELINE STAGE LOOKUP FP: :tcam_sz=1024(0x400), tcam_slices=4, tcam_ext_numb=0, GID 3: gid=0x3, instance=0 mode=Double, stage=Egress lookup=Enabled, ActionResId={-1}, pbmp={0x000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000888888888888888c2222222222223e23} qset={StageEgress, MirrorCopy, CpuQueue, IngressClassField, HiGigDstGport}, selcodes[0]= { FPF3=KEY6 Intraslice=Primary slice. {StageEgress->HiGigDstGport}, selcodes[1]= { FPF3=KEY4 Intraslice=Primary slice. {MirrorCopy->CpuQueue->IngressClassField}, group_priority= -2147483647 slice_primary = {slice_number=0, Entry count=512(0x200), Entry free=512(0x200)}, slice_secondary = {slice_number=1} group_status={prio_min=-2147483647, prio_max=2147483647, entries_total=1024, entries_free=1024, counters_total=2048, counters_free=2048, meters_total=1536, meters_free=1536} Intra-slice double wide group, GID 2: gid=0x2, instance=0 mode=IntraSliceDouble, stage=Lookup lookup=Enabled, ActionResId={-1}, pbmp={0x000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000888888888888888c2222222222223e23} ...
- TeCHSupport vfp [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect VLAN field processor (VFP) debug information. Diag commands run: fp show. Software dumps: dump sw vfp. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport vfp diag >>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "fp show" start>>>>>>>>>>>>>>>>>>>>>>>>>>>> FP: Range ID=1, flag=0x1, min=34048, max=35072, hw_index=0(0), style=BCM56504 FP: unit 0: PIPELINE STAGE INGRESS FP: :tcam_sz=18432(0x4800), tcam_slices=12, tcam_ext_numb=0, PIPELINE STAGE EGRESS FP: :tcam_sz=2048(0x800), tcam_slices=4, tcam_ext_numb=0, PIPELINE STAGE LOOKUP FP: :tcam_sz=1024(0x400), tcam_slices=4, tcam_ext_numb=0, GID 3: gid=0x3, instance=0 mode=Double, stage=Egress lookup=Enabled, ActionResId={-1}, pbmp={0x000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000888888888888888c2222222222223e23} qset={StageEgress, MirrorCopy, CpuQueue, IngressClassField, HiGigDstGport}, selcodes[0]= { FPF3=KEY6 Intraslice=Primary slice. {StageEgress->HiGigDstGport}, selcodes[1]= { FPF3=KEY4 Intraslice=Primary slice. {MirrorCopy->CpuQueue->IngressClassField}, group_priority= -2147483647 slice_primary = {slice_number=0, Entry count=512(0x200), Entry free=512(0x200)}, slice_secondary = {slice_number=1} group_status={prio_min=-2147483647, prio_max=2147483647, entries_total=1024, entries_free=1024, counters_total=2048, counters_free=2048, meters_total=1536, meters_free=1536} Intra-slice double wide group, GID 2: gid=0x2, instance=0 mode=IntraSliceDouble, stage=Lookup lookup=Enabled, ActionResId={-1}, pbmp={0x000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000888888888888888c2222222222223e23} ...
- TeCHSupport efp [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect egress field processor (EFP) debug information. Diag commands run: fp show. Software dumps: dump sw efp. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport efp diag >>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "fp show" start>>>>>>>>>>>>>>>>>>>>>>>>>>>> FP: Range ID=1, flag=0x1, min=34048, max=35072, hw_index=0(0), style=BCM56504 FP: unit 0: PIPELINE STAGE INGRESS FP: :tcam_sz=18432(0x4800), tcam_slices=12, tcam_ext_numb=0, PIPELINE STAGE EGRESS FP: :tcam_sz=2048(0x800), tcam_slices=4, tcam_ext_numb=0, PIPELINE STAGE LOOKUP FP: :tcam_sz=1024(0x400), tcam_slices=4, tcam_ext_numb=0, GID 3: gid=0x3, instance=0 mode=Double, stage=Egress lookup=Enabled, ActionResId={-1}, pbmp={0x000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000888888888888888c2222222222223e23} qset={StageEgress, MirrorCopy, CpuQueue, IngressClassField, HiGigDstGport}, selcodes[0]= { FPF3=KEY6 Intraslice=Primary slice. {StageEgress->HiGigDstGport}, selcodes[1]= { FPF3=KEY4 Intraslice=Primary slice. {MirrorCopy->CpuQueue->IngressClassField}, group_priority= -2147483647 slice_primary = {slice_number=0, Entry count=512(0x200), Entry free=512(0x200)}, slice_secondary = {slice_number=1} group_status={prio_min=-2147483647, prio_max=2147483647, entries_total=1024, entries_free=1024, counters_total=2048, counters_free=2048, meters_total=1536, meters_free=1536} Intra-slice double wide group, GID 2: gid=0x2, instance=0 mode=IntraSliceDouble, stage=Lookup lookup=Enabled, ActionResId={-1}, pbmp={0x000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000888888888888888c2222222222223e23} ...
- TeCHSupport mpls [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect MPLS debug information. Diag commands run: l2 show, vlan show, the vlan translate show family, l3 intf/egress/multipath/l3table/defip show, multicast show, trunk show. Software dumps: dump sw mpls. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport mpls diag >>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "l2 show" start>>>>>>>>>>>>>>>>>>>>>>>>>>>> mac=e0:39:d7:88:3b:00 vlan=1 GPORT=0x0 modid=0 port=0/cpu0 Static CPU <<<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "l2 show" end<<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "vlan show" start>>>>>>>>>>>>>>>>>>>>>>>>>>> vlan 1 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN vlan 902 ports xe3 (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000001000), untagged xe3 (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000001000) MCAST_FLOOD_UNKNOWN vlan 3999 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN vlan 4095 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN <<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "vlan show" end<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>Output of "vlan translate show" start>>>>>>>>>>>>>>>>>>>>>> u = 0, modid = 0 port = 12, old_vid = 902, new_vid = 0, prio = 0 <<<<<<<<<<<<<<<<<<<<<<<Output of "vlan translate show" end<<<<<<<<<<<<<<<<<<<<<<< Time taken to execute "vlan translate show" is 00:00:01 (hh:mm:ss). >>>>>>>>>>>>>>>>>>Output of "vlan action translate show" start>>>>>>>>>>>>>>>>>> Port=12, Modid=0, KeyType=PortOuter, OldOuterVlan=902, OldInnerVlan=-- DT: Outer=None OuterPrio=None Inner=None InnerPrio=None OT: Outer=Delete OuterPrio=Replace Inner=None IT: Outer=Delete Inner=None InnerPrio=Delete ...
- TeCHSupport cos [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect CoS and queueing debug information. Diag commands run: ps, show pmap, cos show, cos port show PBM=all, cos discard_show, cos bandwidth_show. Software dumps: d sw cosq. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport cos diag >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "ps" start>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> ena/ speed/ link auto STP lrn inter max cut loop port link Lns duplex scan neg? state pause discrd ops face frame thru? back encap ce0( 1) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce1( 5) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE xe0( 9) up 1 10G FD SW No Forward Untag F XFI 9122 No IEEE xe1( 10) up 1 10G FD SW No Forward Untag F XFI 9122 No IEEE xe2( 11) up 1 10G FD SW No Forward Untag F XFI 9122 No IEEE xe3( 12) up 1 10G FD SW No Forward None F XFI 9122 No IEEE ce2( 13) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce3( 17) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce4( 21) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce5( 25) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce6( 29) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce7( 33) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce8( 37) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce9( 41) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce10( 45) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce11( 49) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce12( 53) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce13( 57) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce14( 61) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE xe4( 66) !ena 1 10G FD SW No Forward Untag F XFI 9122 No IEEE ce15( 67) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce16( 71) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce17( 75) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce18( 79) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce19( 83) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ...
- TeCHSupport mmu [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect MMU (buffers and scheduling) debug information. Diag commands run: ps, show pmap, lls sw, hsp. Software dumps: d sw cosq. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport mmu diag >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "ps" start>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> ena/ speed/ link auto STP lrn inter max cut loop port link Lns duplex scan neg? state pause discrd ops face frame thru? back encap ce0( 1) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce1( 5) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE xe0( 9) up 1 10G FD SW No Forward Untag F XFI 9122 No IEEE xe1( 10) up 1 10G FD SW No Forward Untag F XFI 9122 No IEEE xe2( 11) up 1 10G FD SW No Forward Untag F XFI 9122 No IEEE xe3( 12) up 1 10G FD SW No Forward None F XFI 9122 No IEEE ce2( 13) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce3( 17) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce4( 21) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce5( 25) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce6( 29) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce7( 33) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce8( 37) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce9( 41) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce10( 45) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce11( 49) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce12( 53) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce13( 57) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce14( 61) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE xe4( 66) !ena 1 10G FD SW No Forward Untag F XFI 9122 No IEEE ce15( 67) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce16( 71) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce17( 75) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce18( 79) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce19( 83) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ...
- TeCHSupport vxlan [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect VXLAN debug information. Diag commands run: l2 show, vlan show, the vlan translate show family, l3 intf/egress/multipath/l3table/defip show, multicast show, trunk show. Software dumps: dump sw vxlan. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport vxlan diag >>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "l2 show" start>>>>>>>>>>>>>>>>>>>>>>>>>>>> mac=e0:39:d7:88:3b:00 vlan=1 GPORT=0x0 modid=0 port=0/cpu0 Static CPU <<<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "l2 show" end<<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "vlan show" start>>>>>>>>>>>>>>>>>>>>>>>>>>> vlan 1 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN vlan 902 ports xe3 (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000001000), untagged xe3 (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000001000) MCAST_FLOOD_UNKNOWN vlan 3999 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN vlan 4095 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN <<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "vlan show" end<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>Output of "vlan translate show" start>>>>>>>>>>>>>>>>>>>>>> u = 0, modid = 0 port = 12, old_vid = 902, new_vid = 0, prio = 0 <<<<<<<<<<<<<<<<<<<<<<<Output of "vlan translate show" end<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>Output of "vlan action translate show" start>>>>>>>>>>>>>>>>>> Port=12, Modid=0, KeyType=PortOuter, OldOuterVlan=902, OldInnerVlan=-- DT: Outer=None OuterPrio=None Inner=None InnerPrio=None OT: Outer=Delete OuterPrio=Replace Inner=None IT: Outer=Delete Inner=None InnerPrio=Delete UT: Outer=Replace Inner=None Policer=0x0 ...
- TeCHSupport niv [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect NIV (VN-tag) debug information. Diag commands run: l2 show, vlan show, the vlan translate show family, l3 intf/egress/multipath/l3table/defip show, multicast show, trunk show. Software dumps: dump sw niv. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport niv diag >>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "l2 show" start>>>>>>>>>>>>>>>>>>>>>>>>>>>> mac=e0:39:d7:88:3b:00 vlan=1 GPORT=0x0 modid=0 port=0/cpu0 Static CPU <<<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "l2 show" end<<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "vlan show" start>>>>>>>>>>>>>>>>>>>>>>>>>>> vlan 1 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN vlan 902 ports xe3 (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000001000), untagged xe3 (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000001000) MCAST_FLOOD_UNKNOWN vlan 3999 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN vlan 4095 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN <<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "vlan show" end<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>Output of "vlan translate show" start>>>>>>>>>>>>>>>>>>>>>> u = 0, modid = 0 port = 12, old_vid = 902, new_vid = 0, prio = 0 <<<<<<<<<<<<<<<<<<<<<<<Output of "vlan translate show" end<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>Output of "vlan action translate show" start>>>>>>>>>>>>>>>>>> Port=12, Modid=0, KeyType=PortOuter, OldOuterVlan=902, OldInnerVlan=-- DT: Outer=None OuterPrio=None Inner=None InnerPrio=None OT: Outer=Delete OuterPrio=Replace Inner=None IT: Outer=Delete Inner=None InnerPrio=Delete UT: Outer=Replace Inner=None Policer=0x0 ...
- TeCHSupport vlan [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect VLAN debug information. Diag commands run: l2 show, vlan show, the vlan translate show family, trunk show. Software dumps: dump sw vlan, dump sw stg, dump sw port, dump sw link. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport vlan diag >>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "l2 show" start>>>>>>>>>>>>>>>>>>>>>>>>>>>> mac=e0:39:d7:88:3b:00 vlan=1 GPORT=0x0 modid=0 port=0/cpu0 Static CPU <<<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "l2 show" end<<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "vlan show" start>>>>>>>>>>>>>>>>>>>>>>>>>>> vlan 1 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN vlan 902 ports xe3 (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000001000), untagged xe3 (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000001000) MCAST_FLOOD_UNKNOWN vlan 3999 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN vlan 4095 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN <<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "vlan show" end<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>Output of "vlan translate show" start>>>>>>>>>>>>>>>>>>>>>> u = 0, modid = 0 port = 12, old_vid = 902, new_vid = 0, prio = 0 <<<<<<<<<<<<<<<<<<<<<<<Output of "vlan translate show" end<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>Output of "vlan action translate show" start>>>>>>>>>>>>>>>>>> Port=12, Modid=0, KeyType=PortOuter, OldOuterVlan=902, OldInnerVlan=-- DT: Outer=None OuterPrio=None Inner=None InnerPrio=None OT: Outer=Delete OuterPrio=Replace Inner=None IT: Outer=Delete Inner=None InnerPrio=Delete UT: Outer=Replace Inner=None Policer=0x0 ...
- TeCHSupport riot [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect RIOT (routing in and out of tunnels) debug information. Diag commands run: l2 show, vlan show, the vlan translate show family, l3 intf/egress/multipath/l3table/defip show, multicast show, trunk show. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport riot diag >>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "l2 show" start>>>>>>>>>>>>>>>>>>>>>>>>>>>> mac=e0:39:d7:88:3b:00 vlan=1 GPORT=0x0 modid=0 port=0/cpu0 Static CPU <<<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "l2 show" end<<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "vlan show" start>>>>>>>>>>>>>>>>>>>>>>>>>>> vlan 1 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN vlan 902 ports xe3 (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000001000), untagged xe3 (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000001000) MCAST_FLOOD_UNKNOWN vlan 3999 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN vlan 4095 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN <<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "vlan show" end<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>Output of "vlan translate show" start>>>>>>>>>>>>>>>>>>>>>> u = 0, modid = 0 port = 12, old_vid = 902, new_vid = 0, prio = 0 <<<<<<<<<<<<<<<<<<<<<<<Output of "vlan translate show" end<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>Output of "vlan action translate show" start>>>>>>>>>>>>>>>>>> Port=12, Modid=0, KeyType=PortOuter, OldOuterVlan=902, OldInnerVlan=-- DT: Outer=None OuterPrio=None Inner=None InnerPrio=None OT: Outer=Delete OuterPrio=Replace Inner=None IT: Outer=Delete Inner=None InnerPrio=Delete UT: Outer=Replace Inner=None Policer=0x0 ...
- TeCHSupport flex_flow [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect FlexFlow debug information. Diag commands run: l2 show, vlan show, the vlan translate show family, l3 intf/egress/multipath/l3table/defip show, multicast show, trunk show. Software dumps: dump sw flex_flow. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport flex_flow diag >>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "l2 show" start>>>>>>>>>>>>>>>>>>>>>>>>>>>> mac=e0:39:d7:88:3b:00 vlan=1 GPORT=0x0 modid=0 port=0/cpu0 Static CPU <<<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "l2 show" end<<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "vlan show" start>>>>>>>>>>>>>>>>>>>>>>>>>>> vlan 1 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN vlan 902 ports xe3 (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000001000), untagged xe3 (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000001000) MCAST_FLOOD_UNKNOWN vlan 3999 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN vlan 4095 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN <<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "vlan show" end<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>Output of "vlan translate show" start>>>>>>>>>>>>>>>>>>>>>> u = 0, modid = 0 port = 12, old_vid = 902, new_vid = 0, prio = 0 <<<<<<<<<<<<<<<<<<<<<<<Output of "vlan translate show" end<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>Output of "vlan action translate show" start>>>>>>>>>>>>>>>>>> Port=12, Modid=0, KeyType=PortOuter, OldOuterVlan=902, OldInnerVlan=-- DT: Outer=None OuterPrio=None Inner=None InnerPrio=None OT: Outer=Delete OuterPrio=Replace Inner=None IT: Outer=Delete Inner=None InnerPrio=Delete UT: Outer=Replace Inner=None Policer=0x0 ...
- TeCHSupport load-balance [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect RTAG7 hashing, DLB, ECMP and trunk debug information. Diag commands run: ps, trunk show. Software dumps: dump sw trunk, dump sw port, dump sw link, dump sw trill, dump sw failover. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport load-balance diag >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "ps" start>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> ena/ speed/ link auto STP lrn inter max cut loop port link Lns duplex scan neg? state pause discrd ops face frame thru? back encap ce0( 1) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce1( 5) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE xe0( 9) up 1 10G FD SW No Forward Untag F XFI 9122 No IEEE xe1( 10) up 1 10G FD SW No Forward Untag F XFI 9122 No IEEE xe2( 11) up 1 10G FD SW No Forward Untag F XFI 9122 No IEEE xe3( 12) up 1 10G FD SW No Forward None F XFI 9122 No IEEE ce2( 13) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce3( 17) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce4( 21) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce5( 25) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce6( 29) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce7( 33) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce8( 37) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce9( 41) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce10( 45) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce11( 49) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce12( 53) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce13( 57) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce14( 61) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE xe4( 66) !ena 1 10G FD SW No Forward Untag F XFI 9122 No IEEE ce15( 67) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce16( 71) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce17( 75) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce18( 79) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ce19( 83) !ena 4 100G FD SW No Forward Untag F CR4 9122 No IEEE ...
- TeCHSupport l3uc [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect L3 unicast debug information. Diag commands run: l2 show, vlan show, l3 intf/egress/multipath/l3table/defip/alpm/ip6host/ip6route/tunnel_init/tunnel_term show, trunk show. Software dumps: dump sw l3. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport l3uc diag >>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "l2 show" start>>>>>>>>>>>>>>>>>>>>>>>>>>>> mac=e0:39:d7:88:3b:00 vlan=1 GPORT=0x0 modid=0 port=0/cpu0 Static CPU <<<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "l2 show" end<<<<<<<<<<<<<<<<<<<<<<<<<<<<< Time taken to execute "l2 show" is 00:00:01 (hh:mm:ss). >>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "vlan show" start>>>>>>>>>>>>>>>>>>>>>>>>>>> vlan 1 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN vlan 902 ports xe3 (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000001000), untagged xe3 (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000001000) MCAST_FLOOD_UNKNOWN vlan 3999 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN vlan 4095 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN <<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "vlan show" end<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>>>>Output of "l3 intf show" start>>>>>>>>>>>>>>>>>>>>>>>>> Free L3INTF entries: 16377 Unit Intf VRF Group VLAN Source Mac MTU TTL Tunnel InnerVlan NATRealm ------------------------------------------------------------------ 0 1 0 0 29574 e0:39:d7:88:3b:00 9100 0 0 0 0 0 8192 0 0 1 00:00:00:00:00:01 16383 0 0 0 0 0 8193 -3 0 1 00:00:01:00:00:01 16383 0 0 0 0 0 8194 -3 0 1 e0:39:d7:88:3b:00 9100 0 0 0 0 0 8195 -3 0 902 e0:39:d7:88:3b:00 9100 0 0 0 0 <<<<<<<<<<<<<<<<<<<<<<<<<<Output of "l3 intf show" end<<<<<<<<<<<<<<<<<<<<<<<<<< ...
- TeCHSupport l3mc [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect L3 multicast debug information. Diag commands run: l2 show, vlan show, l3 intf/egress/multipath show, ipmc table/egr/counter/ip6table show. Software dumps: dump sw mcast, dump sw multicast. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport l3mc diag >>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "l2 show" start>>>>>>>>>>>>>>>>>>>>>>>>>>>> mac=e0:39:d7:88:3b:00 vlan=1 GPORT=0x0 modid=0 port=0/cpu0 Static CPU <<<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "l2 show" end<<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "vlan show" start>>>>>>>>>>>>>>>>>>>>>>>>>>> vlan 1 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN vlan 902 ports xe3 (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000001000), untagged xe3 (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000001000) MCAST_FLOOD_UNKNOWN vlan 3999 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN vlan 4095 ports none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000), untagged none (0x00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000) MCAST_FLOOD_UNKNOWN <<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "vlan show" end<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>>>>Output of "l3 intf show" start>>>>>>>>>>>>>>>>>>>>>>>>> Free L3INTF entries: 16377 Unit Intf VRF Group VLAN Source Mac MTU TTL Tunnel InnerVlan NATRealm ------------------------------------------------------------------ 0 1 0 0 29574 e0:39:d7:88:3b:00 9100 0 0 0 0 0 8192 0 0 1 00:00:00:00:00:01 16383 0 0 0 0 0 8193 -3 0 1 00:00:01:00:00:01 16383 0 0 0 0 0 8194 -3 0 1 e0:39:d7:88:3b:00 9100 0 0 0 0 0 8195 -3 0 902 e0:39:d7:88:3b:00 9100 0 0 0 0 <<<<<<<<<<<<<<<<<<<<<<<<<<Output of "l3 intf show" end<<<<<<<<<<<<<<<<<<<<<<<<<< Time taken to execute "l3 intf show" is 00:00:01 (hh:mm:ss). ...
- TeCHSupport cmic [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect CMIC debug information. Diag commands run: ver, soc. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport cmic >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "ver" start>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Broadcom Command Monitor: Copyright (c) 1998-2026 Broadcom Release: sdk-6.5.35-SP1 built 20260930 (Wed Sep 30 11:49:47 2026) SDK version 6.5.35 : 1.19 From root@4206781cd07d:/__w/1/s/output/x86-xgsall-deb/xgs-sdk-src/hsdk-all-6.5.35 Platform: unknown OS: Unix (Posix) <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "ver" end<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>Output of "soc" start>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Unit 0 Driver Control Structure: Chip=BCM56870_A0 Rev=0x01 Driver=BCM56870_A0 Flags=0x48103: attached initialized mem-clear-use-dma; board type 0x0 CM: Base=0x7fe873800000 Disabled: reg_flags=0x100 mem_flags=0x0 SchanOps=1850363953 MMUdbg=0 LinkPause=0 Counter: int=1000000us per=1158880us dmaBuf=0x7fe871830280 EvictInvalidPoolIdCount=0 BulkDmaErrorCount=0 CounterDmaDurationUsec=115684 CounterErrorRestartCount=0 Timeout: Schan=0(300000us) MIIM=0(1000000us) SchanMemRead=0 SchanMemWrite=0 SchanRegRead=0 SchanRegWrite=0 SchanTblInsert=0 SchanTblDelete=0 SchanTblLookup=0 Intr: Total=18640770 Sc=0 ScErr=0 MMU/ARLErr=0 ...
- TeCHSupport warmboot [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect warm-boot debug information. Diag commands run: warmboot scache, warmboot storage, warmboot usage, warmboot show. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport warmboot >>>>>>>>>>>>>>>>>>>>>>>>Output of "warmboot scache" start>>>>>>>>>>>>>>>>>>>>>>>> scache block size checks: PASS scache block sanity checks: N/A scache info: flags=0x0000 last_offset=0x0529ea74 scache handles: idx handle offset size used cache lock flags 0 0x002d0009 0x0529e9d4 0x000000a0 0x00000000 0x55975666c168 0x55975666c0e0 0x0001 1 0x002d0005 0x0529e97c 0x00000058 0x00000000 0x55975666c028 0x55975666bfa0 0x0001 2 0x002d0004 0x0529df4c 0x00000a30 0x00000000 0x55975666b508 0x55975666b480 0x0001 3 0x00290000 0x0529bb34 0x00002418 0x00000000 0x5597566683c8 0x559756668340 0x0001 4 0x00370001 0x0529bb20 0x00000014 0x00000000 0x559756667178 0x5597566670f0 0x0001 5 0x00360000 0x0529a648 0x000014d8 0x00000000 0x559756665b38 0x559756665ab0 0x0001 6 0x00140000 0x0529a548 0x00000100 0x00000000 0x5597566636f8 0x559756663670 0x0001 7 0x001f0000 0x05296538 0x00004010 0x00000000 0x55975662f2f8 0x55975662f270 0x0001 8 0x00280000 0x05149d28 0x0014c810 0x00000000 0x559756442958 0x5597564428d0 0x0001 9 0x003d0000 0x05146918 0x00003410 0x00000000 0x55975643f458 0x55975643f3d0 0x0001 10 0x00300000 0x050260ec 0x0012082c 0x00000000 0x55975631a4b8 0x55975631a430 0x0001 11 0x001e0000 0x05025d08 0x000003e4 0x00000000 0x55975584e7a8 0x5597561f1a00 0x0001 12 0x002f0000 0x05025cf8 0x00000010 0x00000000 0x5597561eec78 0x5597561eebf0 0x0001 13 0x00180000 0x04fb5ce8 0x00070010 0x00000000 0x55975617cb78 0x55975617caf0 0x0001 14 0x00160000 0x04f3a4fc 0x0007b7ec 0x00000000 0x5597560409c8 0x559756040940 0x0001 15 0x000d0000 0x04f19ce0 0x0002081c 0x00000000 0x559755dd6048 0x559755dd5fc0 0x0001 16 0x00080000 0x04ed24d0 0x00047810 0x00000000 0x559755aaf9c8 0x559755aaf940 0x0001 17 0x000b0000 0x04eb2850 0x0001fc80 0x00000000 0x5597558c6c08 0x5597558c6b80 0x0001 18 0x001b0000 0x04eb283c 0x00000014 0x00000000 0x5597558c6b08 0x5597558c6a80 0x0001 19 0x00120000 0x04eb2760 0x000000dc 0x00000000 0x5597544861d8 0x5597558c3f30 0x0001 20 0x000a0001 0x04eb2748 0x00000018 0x00000000 0x5597557de108 0x5597557d91c0 0x0001 21 0x000a0000 0x04eb1f24 0x00000824 0x00000000 0x5597558c0098 0x5597557ce150 0x0001 ...
- TeCHSupport cancun [diag] [reg] [mem] [sw] [verbose] [list] [generate-script]
Collect CANCUN debug information. Diag commands run: cancun stat. Feature-specific registers and memories are dumped as well. Read-only.
Hardware-validated
drivshell> techsupport cancun >>>>>>>>>>>>>>>>>>>>>>>>>>Output of "cancun stat" start>>>>>>>>>>>>>>>>>>>>>>>>>> UNIT0 CANCUN: CIH: LOADED Ver: 06.15.00 CMH: LOADED Ver: 06.15.00 SDK Ver: 06.05.35 CCH: LOADED Ver: 06.15.00 SDK Ver: 06.05.35 CEH: LOADED Ver: 06.15.00 SDK Ver: 06.05.35 CFH: LOADED Ver: 06.15.00 <<<<<<<<<<<<<<<<<<<<<<<<<<<Output of "cancun stat" end<<<<<<<<<<<<<<<<<<<<<<<<<<< >>>>>>>>>>>Output of "dump chg IP_PARSER0_HME_STAGE_TCAM_ONLY_0" start>>>>>>>>>>> IP_PARSER0_HME_STAGE_TCAM_ONLY_0.ipipe0[12]: <VALID=3,PKT_DATA_MASK=0xf8000000000000270000000000000000f00000,PKT_DATA=0xf8000000000000200000000000000000000000,MASK=0xf8000000000000270000000000000000f000000000ffff00,KEY=0xf80000000000002000000000000000000000000000000300,IN_CONTEXT_ID_MASK=0xffff,IN_CONTEXT_ID=3,> IP_PARSER0_HME_STAGE_TCAM_ONLY_0.ipipe0[13]: <VALID=3,PKT_DATA_MASK=0xf8000000000000270000000000000000f00000,PKT_DATA=0xf8000000000000200000000000000000100000,MASK=0xf8000000000000270000000000000000f000000000ffff00,KEY=0xf80000000000002000000000000000001000000000000300,IN_CONTEXT_ID_MASK=0xffff,IN_CONTEXT_ID=3,> IP_PARSER0_HME_STAGE_TCAM_ONLY_0.ipipe0[14]: <VALID=3,PKT_DATA_MASK=0xf8000000000000270000000000000000f00000,PKT_DATA=0xf8000000000000200000000000000000200000,MASK=0xf8000000000000270000000000000000f000000000ffff00,KEY=0xf80000000000002000000000000000002000000000000300,IN_CONTEXT_ID_MASK=0xffff,IN_CONTEXT_ID=3,> ...
Built-in help
Usages: techsupport basic - collects basic config/setup information from switch techsupport all - Executes all techsupport commands supported on switch techSupport <feature_name> [diag] [reg] [mem] [list] [sw] [verbose]- collects feature specific debug information When <feature_name> is etrap - collects etrap related debug information When <feature_name> is int - collects int related debug information When <feature_name> is histogram - collects histogram related debug information When <feature_name> is alpm - collects alpm related debug information When <feature_name> is cos - collects cos related debug information When <feature_name> is efp - collects efp related debug information When <feature_name> is ifp - collects ifp related debug information When <feature_name> is load-balance - collects RTAG7,DLB,ECMP and trunk related debug information When <feature_name> is l3uc - collects L3 unicast related debug information When <feature_name> is l3mc - collects L3 multicast related debug information When <feature_name> is mpls - collects mpls related debug information When <feature_name> is mmu - collects mmu related debug information When <feature_name> is niv - collects niv related debug information When <feature_name> is vfp - collects vfp related debug information When <feature_name> is riot - collects riot related debug information When <feature_name> is oam - collects oam related debug information When <feature_name> is vxlan - collects vxlan related debug information When <feature_name> is vlan - collects vlan related debug information When <feature_name> is tcb - collects tcb related debug information When <feature_name> is dgm - collects dgm related debug information When <feature_name> is pstat - collects pstat related debug information When <feature_name> is flex_flow - collects FlexFlow related debug information When <feature_name> is PHY - collects Phy related debug information When <feature_name> is LEDUP - collects CMIC led-processor debug information When <feature_name> is cmic - collects CMIC debug information When <feature_name> is cancun - collects Cancun debug information When <feature_name> is visibility - collects packet trace information for packet data techsupport visibility file/data=<val> sourceport=<val> options=<flags> [raw] file or data- packet data, sourceport- source port for packet, (mandatory) When <feature_name> is warmboot - collects warmboot info When <feature_name> is flowtracker - collects flowtracker debug information raw- dumps raw memory content (optional) options- packet trace flags (optional) - 0x1 BCM_PKT_TRACE_LEARN - 0x2 BCM_PKT_TRACE_NO_IFP - 0x4 BCM_PKT_TRACE_FORWARD - 0x8 BCM_PKT_TRACE_DROP_TO_MMU - 0x10 BCM_PKT_TRACE_DROP_TO_EGRFurther reading
SDK-6.5.20 HSDK Getting Started Guide (GS-SDK6520-R), plus SDK-6.5.20/21/22 Release Notes (RN-SDK65xx-R), BISDN Linux bundle-debug-info support script.